logobypixcl
01 34 84 21 93

Contact

Mon compte

Mes favoris

Primaire 3M 86A – bidon de 0,47 L – à l’unité

50,42 € HT 60,50 € TTC

Primaire spécial plastique. Permet une adhésion plus rapide et plus forte. Conditionnement en bidon de 250 ml

Réf Pixcl : Prim86A – Réf 3M : 14793

UGS : Prim86A Catégorie : Étiquette :

Prix dégressifs et délais

à l’unité
x 1 x 6 x 12 x 24 x 48
bidon de 0,47 L 44,37 € 43,36 € 42,35 €
Délais : PuceVerte En stock    PuceJaune 1 à 2 semaines    PuceOrange 3 à 4 semaines    PuceOrange 5 à 8 semaines

Description

3M™ Adhesion Promoter 86A is a liquid“primer” designed to be used with 3M™Polyurethane Protective Tapes and Boots andother acrylic adhesives to enhance initialadhesion in demanding situations.3M 86A promoter is designed to promotefaster initial adhesion to certain types ofsurfaces, such as polyurethane paint, epoxyprimers, or epoxy composites. It is notintended for use where the acrylic adhesivewould be in direct contact with aluminum,stainless steel, carbon, steel, or glass.

Caractéristiques

Application Use
Note: When using solvents, extinguish all ignition sources, including pilot lights. Readand follow manufacturer’s warnings and directions for use

1)Surface PreparationThe bonding surface must be smooth, clean, dry and free of foreign matter. If necessary, thesurface should be sanded to the smoothness attainable with 320 grit sandpaper. Clean thesurface with isopropyl alcohol and allow the surface to dry prior to the application of 3M™Adhesion Promoter 86A.* Application of 3M Promoter 86A on bare metal surfaces does notappreciably enhance adhesive values. The danger in using 3M Promoter 86A on metalsurfaces is that it may transfer to the tape adhesive, if the tape is lifted for repositioning. Ifthis transfer occurs, the adhesive of the protective tape will be compromised.Note: Towels or cloths used in the cleaning process should be untreated and lint free(i.e. – cheesecloth or Kimwipe®)

2)Apply 3M 86A PromoterWipe the surface with the pre-saturated 3M 86A Promoter wipe or with cheesecloth wettedwith 3M 86A Promoter, using the minimumamount that will coat desired surface. More isnot better.Allow to dry for 10 minutes. For best results, apply 3M Polyurethane ProtectiveTape with acrylic adhesive within two hours to the promoted surface.Note: In many applications only the outer most edges of the application area may requireuse of 3M 86A Promoter.Note: 3M Tape and Boot applications over 3M 86A Promoter will be more difficult toremove.Note: If desired, 3M 86A Promoter may be sprayed on the surface, using most conventionalspray equipment. If dilution is required, it may be done with isopropyl alcohol.*

Télécharger la fiche technique : primaire-3m-86a-tec-by-pixcl.pdf
Télécharger la fiche de sécurité : primaire-3m-86a-fds-by-pixcl.pdf

Poids 0.7 kg
Dimensions .47 cm
Longueur

0,47 L

Avis

Il n’y a pas encore d’avis.

Seuls les clients connectés ayant acheté ce produit ont la possibilité de laisser un avis.

DISTRIBUTEUR AGREE

logo velcro logo 3m logo tesa

MOYENS DE PAIEMENT

logo visa logo mastercard logo paypal
logo cheque logo mandat logo virement

LIVRAISON

logo colissimo logo mondial relais logo tnt
logo frequenceo lettre suivie logo chronopost